Buchi KjelSampler K-377 Manual de usuario Pagina 71
- Pagina / 160
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6 Operation
71
K-375/376/377 Operation Manual, Version B
(screenshot stretched)
Priming
Priming is used to prepare the entire system. This
preparation procedure includes the distillation and
titration with a clean and empty sample tube, as
well as the dosing of chemicals. It is recommended
to perform a priming at least once a day, before
starting analysis. The priming procedure is similar to
a sample determination method and can be modi-
fied.
Priming Parameters
Select Yes for “Preheating before priming” if prior to
the priming procedure a preheating procedure shall
be performed.
Set the number of “Priming runs”.
Set “Priming cycle” to “Via sampler”, if the priming
procedure should be performed via a present
sampler. (Only visible if a sampler has been config-
ured under “Settings”.)
The other parameter sets Distillation Parameters,
Titration Parameters, and Aspiration Param-
eters are just the same like within a method. A
detailed explanation can be found in the section
“6.8.1 Method”.
Press START to start the priming procedure.
Press FACTORY DEFAULTS to reset the settings
of this screen.
NOTE
If only one priming cycle is selected and no aspira-
tion, no aspiration will be done at all.
If more than one priming cycle is selected and no
aspiration, the sample tube and the receiving vessel
will be aspirated between the single priming cycles,
but not after the last cycle has been performed –
instead the system will be stopped after the last
run.
- Operation Manual 1
- Document History 3
- Table of contents 5
- 1 About this manual 10
- 2 Safety 11
- SIGNAL WORD 12
- 2.5 Product safety 14
- 2.6 General safety rules 17
- 2 Safety 18
- 3 Technical data 19
- Product Order number 20
- Number of 23
- Product Order 23
- 3.2 Technical data overview 26
- 3.3 Titration solution 27
- 3.5 Reference substances 29
- 3.6 Materials used 29
- Part Material Material code 30
- 4 Description of function 31
- 4.3 Standby function 35
- 4.4 System preparation 35
- 4.6 Different methods 38
- 4.7 Blank values 39
- 4.8 Reference substances 39
- 4.9 Result Groups 39
- 5 Putting into operation 43
- 5.2 Electrical connections 44
- 2O is expected 49
- 3BO3) pump 50
- 5.5 Buret unit for titrant 51
- 5.6 Storage tank connection 52
- 5.7 Level sensors 53
- 5.9 Preparing the system 57
- 2O, H3BO3 and NaOH 58
- 2O, NaOH or H3BO3) 58
- 6 Operation 59
- Fig. 6.2 Title bar 61
- Fig. 6.3 Bottom bar 61
- Icon Meaning 62
- 6.3 User concept 63
- Fig. 6.5 Listed item 64
- 6.5 The status view 65
- 6.5.3 INFO display 68
- 6.6 Determination 69
- 2O, NaOH or 75
- 6.7 Results 89
- 6.8 Determination Parameters 97
- 6.9 Device 108
- Dosage volume in status view 110
- 6 Operation 118
- 7 Maintenance 119
- 7.1 Daily maintenance 120
- 2O volume 121
- 7.2 Weekly maintenance 123
- 7.3 Monthly maintenance 125
- 2O volume: 0 mL 126
- 7.4 Half-yearly maintenance 128
- 7.5 Yearly maintenance 133
- 7.6 Replace every two years 137
- Soiling Treatment Comments 139
- 7.8 Customer service 142
- 8 Troubleshooting 143
- 2SO4 in wrong 145
- 8 Troubleshooting 152
- 9 Taking out of operation 153
- 9.3 Storage/shipping 154
- 9.4 Disposal 154
- 10 Spare parts 155
- 10.2 Spare parts K-376/K-377 156
- Quality in your hands 160
Relacionado con productos y manuales para Instrumentos de medición Buchi KjelSampler K-377
(74 paginas)Arnova 97 G4 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Arnova 97 G4.
Nous fournissons des manuels en pdf 1 Arnova 97 G4 à télécharger gratuitement par type de document : Instructions d'exploitation
Comentarios a estos manuales